Key Points Of Aluminum Alloy Cable Trays Construction Technology

May 26, 2025 Leave a message

Aluminum alloy Cable Tray is widely used in power, communication, construction and other fields due to its advantages of light weight, corrosion resistance, high strength and convenient installation. The following are the key points of its construction technology, which are explained in steps:

Aluminum alloy Cable Tray1

Cold chain transportation of semi-finished food project

Aluminum alloy Cable Tray2

Cold chain transportation of semi-finished food project

Aluminum alloy Cable Tray3

Cold chain transportation of semi-finished food project

 

 

I. Preparation before construction

 

1. Drawing review and technical disclosure
- Check the design drawings to confirm the cable tray path, specifications, elevation and intersection with other pipelines.
- Clarify the construction specifications (such as "Cable Tray Installation Standard Atlas" 04D701-3).

2. Material acceptance
- Check the material certification of aluminum alloy cable tray and accessories (such as corrosion resistance, load level).
- Appearance inspection: no deformation, scratches, and oxide film damage.

3. Tool preparation
- Cutting machine (special for aluminum alloy), level, laser rangefinder, torque wrench, insulating gasket, etc.
 

II. Support and hanger installation

 

1. Positioning and laying out
- Position according to the line of the drawing to ensure horizontal and vertical, and avoid conflict with ventilation pipes and water pipes.
- When installed horizontally, the spacing between supports and hangers is usually 1.5~2m (large loads need to be increased); when installed vertically, it is ≤1.5m.
2. Fixing of supports
- Concrete structure: Use expansion bolts (M10 and above) to avoid hitting the steel bars.
- Steel structure: Welding or clamp fixing, anti-corrosion treatment is required after welding.

 

III. Installation of Cable tray frame body

 

1. Cutting and connection
- Use special cutting tools to remove burrs and perform anti-corrosion treatment on the cut (such as spraying special anti-corrosion paint for aluminum alloy).
- The connecting plate bolts should be installed from the inside to the outside, the nuts are located on the outside of the cable tray, and the torque must meet the specifications (such as the torque of M8 bolts is about 20N·m).
2. Horizontal installation
- The slope of ordinary places is ≥0.1%, and inclination or drainage holes are required in flammable and explosive places.
- The spacing with other pipelines: parallel to power cables is ≥0.3m, and cross ≥0.5m.
3. Vertical installation
- Use special vertical fixing clamps, with at least 2 fixing points for each cable tray section.
- Add 45° or 90° elbows at the bends to avoid cable damage caused by right-angle bends.
4. Grounding treatment
- Connect the grounding wire (≥4mm² copper core wire) between cable trays, and connect it to the grounding trunk line at no less than 2 points along the entire length.
- Galvanized connecting plates do not need to be connected, but the contact surface must be well conductive.

 

IV. Construction in special environments

 

1. Corrosive environment
- Use highly anti-corrosion aluminum alloys such as 5052 or 6061, or spray epoxy resin on the surface.
- Avoid direct contact with copper and steel (need to be isolated with insulating gaskets).
2. Outdoor installation
- Add a cover plate to the cable tray to prevent rain and snow, and apply sealant at the connection.
- Consider thermal expansion and contraction, and set expansion joints every 30m.

 

V. Quality Acceptance

 

1. Main Control Items
- Ground resistance ≤4Ω, horizontal deviation of cable tray ≤2mm/m, vertical deviation ≤3mm/m.
2. General Items
- No scratches on the surface, bolts in the same direction, and tight fire blocking (when crossing fire partitions).

 

VI. Safety Precautions

 

1. Wear a safety belt for high-altitude work and use qualified scaffolding.
2. Wear goggles when cutting to avoid aluminum chips splashing.
3. It is strictly forbidden to stack heavy objects on the cable tray or climb an unfixed cable tray.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry